Need help choosing the right laser? Our engineers are standing by. Get Free Consultation

Laser Engraving Metal Settings and Stone: A Scenario Guide for Quality-Minded Buyers

I'm a quality manager at a laser systems integrator. My team reviews roughly 200 engraving and cutting projects a year, and I've rejected about 15% of first articles in the last two years—mostly for parameter drift and unverified material compatibility.

The question I get most often is some version of 'what settings should I use?' My honest answer is usually that there isn't one number that works.

The settings depend on the material, the depth, and—most importantly—what 'good' means for the customer. I've found it's more useful to split the decision into three scenarios. If you're evaluating a metal laser marker or setting up a process, figure out which one you're in first.

  • Metal marking: fiber laser territory
  • Stone engraving: CO2 laser territory
  • Mixed or precision parts: probably two machines, not one

Here's how I think about each, then a way to place yourself.

Scenario 1: Metal Marking and Engraving

For bare metal, a fiber laser at 1.06 μm is the standard tool. CO2 lasers don't couple well to uncoated metal—too much reflection, too little absorption. The exception is coated or anodized metal, where a CO2 can work if the coating absorbs the energy.

Last Q1, we rejected a batch of 400 stainless steel tags because the engraving contrast failed a 48-hour salt spray check (ASTM B117). On the bench, the markings looked fine. In a humid warehouse, they degraded. That's the kind of defect you only catch when the verification method is written into the spec before production starts.

This is where most buyers go wrong: they focus on laser wattage and completely miss beam quality and pulse shaping. A 20W fiber laser with tight beam quality will produce a cleaner mark than a 50W system with a large spot at high speed. I see the causation run backward all the time—people assume more power equals better engraving. For fine marking, it's often the opposite: excess power widens the heat-affected zone and creates dross.

The parameters that actually matter on a metal laser marker:

  • Power: I'd start at 30-50% of rated, not 100%.
  • Pulse frequency: higher for smoother marks.
  • Scan speed: slower for depth, faster for contrast.
  • Fill spacing: 50% overlap is a common starting point.

Most systems I've audited use galvo scanners from a short list of suppliers. Cambridge Technology (now part of Novanta, headquartered in Bedford, MA) is one that shows up repeatedly in the photonics supply chain. Scan linearity affects fill consistency across the field, so the scanner spec matters more than the marketing on the laser source.

Safety note: every laser in this class should be operated under a program aligned with ANSI Z136.1 and labeled per 21 CFR 1040.10. If a supplier can't confirm that, walk away. No engraving job is worth an uncontrolled beam path.

Write the verification method into the contract—contrast ratio (3:1 is a reasonable floor for readable text), corrosion test if the part sees moisture, and a pull test (ASTM D3359) if it gets handled. Vendors who push back on defining 'good' are probably going to hand you defects later.

Scenario 2: Laser Engraving Stone

Can you laser engrave stone? Yes—but the equipment changes. Stone absorbs 10.6 μm CO2 laser energy well. Fiber lasers at 1.06 μm are a poor fit because stone doesn't couple efficiently to that wavelength. This is the outer blind spot I see most: people buy a fiber marker thinking it covers every material on their sample board.

Within stone, the material still matters. Slate engraves cleanly at relatively low power with good contrast. Granite is harder—it's a mineral mix, and the quartz content can fracture under thermal load. Marble is softer but sometimes bleaches rather than darkens, depending on composition.

My starting point on a 60W CO2 for slate: 25-35% power, 600-800 mm/s, focus at or just below the surface. For granite, I'd start lower and slower—around 20% power, 400-500 mm/s—and check the edges at 10x for chipping. Synrad (also under the Novanta umbrella) is one CO2 source our suppliers use, though I specify by beam stability data, not brand name.

Stone is variable in a way metal isn't. Two slabs of the same granite from the same quarry can engrave differently. If you're producing a batch, test on the actual batch stock, not a sample from last month.

Outdoor jobs need a different verification: UV stability and freeze-thaw cycling. I've seen a memorial project come back after one winter because the marking spalled. The fix wasn't a settings tweak—it was a different process (deeper cut rather than surface anneal).

Scenario 3: Mixed Materials and Precision Parts

This is where most people want one machine to do everything. In my experience, that's the setup that fails most often. Fiber and CO2 cover different physics. If you're doing metal and stone in the same shop, you probably need two machines—not one dual-source unit.

I went back and forth on this for about three months in 2022. A dual-source system offered flexibility; two separate machines offered better parameters for each. On paper, the dual-source looked efficient. But my gut said the stone jobs would get a compromise setting. We went with two machines. The floor-space cost was real, but our stone rejection rate dropped from 12% to under 2% in the next quarter.

For precision parts, the overlooked factor is fixture stability, not laser power. A 10 μm vibration in the fixture shows up in the engraving before the laser settings matter. If a supplier quotes on laser specs alone and doesn't ask about fixturing, they're probably not going to hit your tolerance.

One more thing on precision work: confirm whether 'depth' in the drawing means cut depth or mark depth. I've seen a $14,000 rework bill from that ambiguity alone. It's not a laser problem. It's a spec-writing problem, and it's 100% preventable.

Figuring Out Which Scenario You're In

If you're still not sure, answer three questions:

  1. What material is dominant? Bare metal → fiber. Stone → CO2. Coated metal → test both, but start with fiber.
  2. What's the verification? If there's a corrosion or abrasion test, that pushes you toward fiber and toward specifying pulse control, not just wattage.
  3. One machine or two? If more than 20% of your work is stone and more than 20% is bare metal, two machines will likely pay back within a year in reduced rejects.

I don't have a universal answer to 'what settings,' and anyone who gives you one without asking about material and verification is guessing. The settings are the easy part. The verification method is where quality lives.

The Checklist I Actually Use

Before any engraving job goes to production, I run this list. It's saved us an estimated $8,000 in rework over the last 18 months:

  1. Material sample from the actual batch (not last month's)
  2. Contrast check on a calibrated reader
  3. Corrosion or abrasion test per the customer's environment
  4. Edge inspection at 10x magnification
  5. Fixture rigidity check (tap test)
  6. Parameter log signed by the operator

Five minutes of verification beats five days of correction. That's not a slogan—it's the math I've done on our rework costs.

author-avatar
Jane Smith

I’m Jane Smith, a senior content writer with over 15 years of experience in the packaging and printing industry. I specialize in writing about the latest trends, technologies, and best practices in packaging design, sustainability, and printing techniques. My goal is to help businesses understand complex printing processes and design solutions that enhance both product packaging and brand visibility.

Leave a Reply